Summary

Concrete grinding can remove many painted floor coatings, but removing the paint film and achieving the intended new floor are different tasks. The existing coating, the concrete underneath and the next finish determine the method and stopping point. Remaining colour needs assessment; grinding deeper to chase it can change the slab’s appearance and height.

By WIRTHFLOOR · Published 31 October 2026

An old painted slab can look like a simple strip-back job. Yet the decision changes depending on whether you want a base for new flooring or concrete that stays exposed. WIRTHFLOOR’s concrete grinding service includes preparing existing floors and removing unwanted surface material.

The useful question is what the removal needs to leave behind. A floor ready for a new coating may have a different acceptable appearance from a floor intended to become a visible decorative surface.

What does a grinder remove from a painted floor?

A floor grinder moves abrasive tooling across the surface. That tooling can break down an existing paint film and abrade the concrete beneath it. The process removes material; it does not dissolve paint or return the slab to an untouched original condition.

Paint may cover a rough surface, sit in small depressions or conceal several earlier layers. As the upper material comes away, the grinder encounters different combinations of coating and concrete. Tooling that works on exposed concrete may respond differently where a coating is thick or soft.

That is why the coating’s behaviour matters alongside its area. A contractor may need a separate removal stage before refining the exposed surface. The right sequence comes from identifying the material and assessing the floor, rather than assuming one pass with one tool will complete it.

Is the remaining colour still paint?

A coloured mark and an intact paint film are not the same observation. A continuous layer, small remnants in surface texture and a discoloured area can look similar from a standing photograph. They may call for different decisions.

Imagine a grey floor with traces of an old blue coating. The raised blue edges may be remaining film. A faint flat shadow elsewhere needs closer inspection before anyone promises that further grinding will remove it. Colour alone does not establish how much material is present or how far below the surface a mark extends.

For an exposed finish, a representative trial area can help show the likely appearance after the agreed preparation. It should include a typical painted section and any visibly different patches. A trial on the easiest corner says little about a heavily recoated strip through the middle of the room.

Further grinding also removes concrete. It may reveal more aggregate or leave a local difference in height. If the last trace of colour would require disproportionate removal, the sensible discussion is about the intended finish and the remaining mark. See what limits concrete removal before treating deeper grinding as an automatic solution.

Two concrete sections showing paint over surface texture and small coating remnants after upper material is removed
Removing upper material can leave coating in lower surface texture.

1. Left: a coating follows the concrete’s surface texture, including a shallow depression.

2. Right: removal across the upper surface leaves a small area of coating in the depression. The dashed line provides a common height reference.

3. The required preparation depends on the next finish.

Will the floor be covered or left visible?

This choice changes what successful paint removal means. Consider the same painted room under three different renovation plans.

A new coating will cover the slab

The priority is a suitable bonding surface for the specified coating. The assessment needs to address remaining material, soundness, contamination and the required surface texture. Simply making the floor look uniformly grey does not prove that the new coating can bond properly.

The Association for Materials Protection and Performance’s concrete preparation guidance starts with inspection of existing coatings, contamination, damage, defects and possible moisture problems. It also explains that preparation methods vary with the condition found. Those are useful distinctions when comparing a cosmetic strip-back with preparation for a complete coating system.

Another floor covering will be installed

The next flooring system determines the acceptance requirements. The installer needs a substrate that suits its adhesive or installation method. Paint removal is one part of that work; moisture, surface strength and flatness still need to be addressed where relevant.

An isolated colour difference may matter less under an opaque covering than it would on exposed concrete. Remaining coating or contamination that affects the bond is a separate issue. Agree on who checks the prepared surface before the covering goes down.

The concrete will remain exposed

Here, appearance becomes part of the result. Paint can hide repairs, patches, cracks and changes in the slab. Removing it reveals those features; it does not make separate pours or old repairs visually identical.

A preparation grind also does not deliver a finished polished floor by itself. Further refinement and the chosen protection are separate parts of the proposed finish. Look at the actual trial area under the room’s lighting before agreeing on an exposed result.

Check unknown paint before disturbing it

The age, colour or apparent condition of a coating cannot confirm its composition. An unidentified old coating needs assessment before a grinder is used on it. A trial grind is a way to assess removal behaviour after that question is resolved.

WorkSafe Queensland’s guidance on working with lead-based paint explains the need to identify and manage the risks of lead paint work. Paint on concrete should not be assumed lead-free. Suspect material may require a specialist removal contractor before ordinary floor preparation can begin.

Grinding concrete also needs suitable dust controls. WorkSafe Queensland’s floor grinder guidance describes water delivery or suitable vacuum collection controls and the management of dust or slurry. The method also needs to account for the coating being removed and the work area.

What should the completed removal look like?

Use the next finish to define the handover. For a recoating job, that means the agreed preparation condition for the coating system. For exposed concrete, it also means an understood appearance, including any retained colour variation or visible repairs.

Record what the trial actually showed: which layers were removed, what remained, how the concrete changed and what further finishing is included. Compare the main floor with edges and corners too. Different access can require different tools, so those areas belong in the agreed result.

A useful scope describes the paint removal and its endpoint together. It identifies any assessment still needed and makes clear whether the price covers preparation only or the subsequent finish. That lets you compare the result being offered, rather than assuming every mention of “paint removal” means the same floor.

WIRTHFLOOR can discuss concrete grinding and surface preparation for an existing painted slab. Get in touch with the floor’s condition and the finish you want next.