Summary

Concrete grinding can remove many identified tile adhesives and glues, but the material on the slab determines the method. Hard cement-based ridges and flexible glue behave differently under tooling. Removing the residue is also separate from preparing the concrete for its next covering or finish. Identify unknown old flooring materials before disturbing them, then agree on the surface the next trade needs.

Lifting old tiles or carpet can leave a floor covered in ridges, sticky patches and thin films. The concrete may be visible between them, but that does not mean it is ready for a new floor. The useful question is what must come off and what condition the slab needs to be in afterwards.

WIRTHFLOOR’s concrete grinding service includes surface preparation and removal work. When discussing an adhesive-covered slab, describe the old covering, the residue you can see and the floor you want next. Those details help define the work more clearly than asking for a quick grind.

Why tile adhesive and glue need different approaches

“Tile glue” can describe several materials. Cement-based tile adhesive normally sets into a hard layer, often retaining the ridges made by a notched trowel. Flexible flooring glue may remain tacky or form a thin, resilient film. There may also be a levelling layer, coating or earlier adhesive beneath what is visible.

Diamond grinding abrades a surface with cutting points held in the tooling. Against a hard residue, that action progressively breaks down the high ridges. A softer adhesive can behave differently: it may smear or clog the working face rather than break away cleanly. More pressure is not automatically a useful answer.

The contractor therefore needs to identify the material and select a removal sequence. Bulk removal or scraping may come before a preparation grind; tooling suited to one layer may be unsuitable for the next. A small trial area can help establish the approach once the material has been identified and any hazardous-material concerns resolved.

Identify unknown old materials first

Do not grind an unidentified old adhesive to see what happens. Some older flooring materials and adhesives contain asbestos. Colour, a photograph or the apparent hardness of the residue cannot establish that a material is safe to disturb.

The NSW Government’s guide to asbestos in adhesives identifies flooring adhesives among the materials where asbestos may occur. If the history is uncertain, arrange competent assessment and any required testing before removal starts. Give the flooring contractor the relevant report, rather than assuming the old tiles coming up cleared the adhesive underneath.

This matters at the enquiry stage. Tell the contractor if a building has several generations of floor coverings, if the material is unknown, or if an asbestos report already exists. A site visit and a removal plan should follow the actual findings.

Removing residue and preparing concrete are separate tasks

A slab can look much cleaner after adhesive removal while still needing further preparation. The next floor relies on the surface immediately beneath it. Dust, weak material or incompatible residue can leave a poor interface even when most of the old glue has gone.

The required surface depends on what follows. A coating needs the specified concrete profile and a sound substrate. A resilient floor covering may need a smoother prepared surface and separate correction of imperfections. Mechanical polishing involves further refinement of the concrete itself. These are different endpoints.

Cross-sections showing ridged adhesive above a concrete slab and the exposed slab after removal
Adhesive removal exposes the concrete; further preparation depends on the next floor.

1. Left: an identified adhesive layer sits above the concrete slab.

2. Right: removing that layer exposes the slab. Flatness, moisture, repairs and the required surface still need assessment.

For example, removing hard adhesive ridges in a former tiled shop may expose small chips left by tile removal. Grinding the remaining ridges does not fill those chips. Whether repairs are needed, and who performs them, should be agreed with the installer of the next system.

WIRTHFLOOR’s explanation of why a clean-looking floor can still have a weak bonding surface explains that distinction further. The aim is a suitable supporting surface, rather than a particular colour or a freshly swept appearance.

Will grinding make the slab flat or ready to polish?

Removing adhesive does not automatically make a floor flat or level. Grinding takes material away. It can reduce a local high area, but it cannot add material to a low spot. A slab can also be flat enough for one use while falling towards a drain or differing in height from the next room.

Check thresholds, door clearances and joins with adjacent floors before setting the scope. If a new covering has a specific flatness requirement, give that requirement to the preparation contractor. Agree whether any filling, levelling or other work sits with a separate trade.

If the plan is to leave the concrete exposed, discuss appearance before treating adhesive removal as the first step towards a finished floor. Old repairs, stains, fixing holes and uneven aggregate exposure may become visible. Removing the surface does not guarantee those features disappear. Read what determines whether an existing slab can be polished before committing to that finish.

Plan dust control, edges and access

Removing residue can involve grinding the concrete beneath it, so dust control belongs in the plan. WorkSafe Queensland’s floor-grinder guidance explains the use of suitable dust collection or integrated water control. Wet work also produces slurry that needs collection before it dries.

Ask how the contractor will manage the work area, adjoining rooms and final clean-up. Discuss access for machinery and extraction equipment, available power, occupied areas and the route for removing waste. A clear work boundary matters particularly when another part of a shop or home remains in use.

Edges need attention too. A large floor grinder cannot reach every corner or fit beneath every fixed cabinet. Ask which perimeter areas are included and whether skirting, doors or other fittings affect access. Do not assume those fittings will be removed as part of the grinding price.

What to provide before asking for a quote

Start with the approximate area and clear photographs of the whole floor, close views of the residue and any changes between rooms. Add what you know about the old covering and any available material assessment. Photographs help explain the enquiry; they do not replace identification or a site assessment.

Then name the intended next floor and share its preparation requirements. Ask whether the proposed scope covers bulk adhesive removal, the preparation grind, edge work, waste removal and any separate repairs. Confirm who checks moisture and who accepts the prepared substrate before the next floor goes down. Grinding alone does not establish moisture suitability.

For a flooring renovation, the best handover is an agreed surface condition and a clear division of work between trades. That avoids booking the installer on the assumption that “glue removed” also means “every preparation task finished”.

WIRTHFLOOR can discuss concrete grinding and surface preparation for your slab. Get in touch with the floor area, residue details and planned finish to discuss the next step.